JXUF105m2
JX
JX0880
Availability: | |
---|---|
Hollow fiber ultrafiltration UF module
1. Product introduction:
JXUF250-Max 80 ultrafiltration membrane is a capillary hollow fibre membrane, which is a kind of polymer material membrane, it is a kind of separation product without phase change. The modified PES material used in this product has good water permeability, mechanical properties, chemical resistance and anti-pollution ability.
JXUF250-Max 80
The membrane module is installed with hollow membrane filament with inner diameter of 0.8mm and outer diameter of 1.3mm. The filtration method is internal pressure, i.e., the raw water is driven by the pressure difference and enters into the inner part of the hollow filament, and permeates through the hollow filament along the radial direction from the inside to the outside. Thus, it can filter
It can remove all kinds of bacteria, colloid, suspended solids, microorganisms and other harmful substances in the raw water.
2. Application:
● Mineral water, mountain spring water and other sterile liquid preparation;
● Drinking treatment of tap water surface water, well water and river water;
● Pre-treatment of RO reverse osmosis device;
● Industrial wastewater treatment, recycling and utilization.
3. Filtration performance
This product achieves the following filtering effects:
Composition of water | Result |
Suspended matter, particles >1um | Remove rate ≥99% |
SDI | Produced ≤3 |
Viruses, Bacteria | >4 log |
Turbidity | Produced <0.1NTU |
TOC | Remove rate 0-25% |
The above data is obtained when the influent turbidity is less than 25NTU.
4. Produce parameters
Performance:
Structure | Out-side in |
Membrane material | Reinforced PVDF |
Membrane area | 105m2 |
Fiber dia. | ID:0.8mm, OD:1.3mm |
Outside dimension | Dia.250mm*2340mm |
Connector size | DN50(Match DN40 joint) |
MWCO | 200000DAL |
Application data:
Typical Filtrate Flux Range | 18800L/H(0.15Mpa,25℃) |
Design Flux | 35-100L/m2.h (0.165Mpa, 25℃) |
Normal working pressure | ≤0.2MPa |
Maximum Transmembrane Pressure | 0.15Mpa |
Maximum backwash Pressure | 0.15Mpa |
Volume of air wash | 0.1-0.15N m3/m2.h |
Air pressure | |
Maximum Operating Temperature | (45°C |
pH Operating Range | 4.0 - 10.0 |
Cleaning pH Range | 4-10 Operating, Cleaning 2-12 |
Operating Mode | Full filtration or Crossflow |
Feed requirements:
A security filter of less than 50 microns is added before the water intake to prevent the machine from being clogged by large particles in the raw water.
The machine is clogged by large particles in the raw water. Note: The ultrafiltration membrane is made of high polymer organic plastic, and the raw water must not contain organic solvents!
Feed Turbidity | ≤25NTU |
Oil | ≤2mg/L |
Feed SS | ≤20mg/L |
Total Iron | ≤1mg/L |
Residual chlorine from continuous inlet water | ≤5ppm |
COD | ≤500mg/L |
Typical Process Conditions
Backwash Pressure | 0.15MPa |
Backwash Flux: | 100 – 150L/m2.h |
Backwash Frequency: | 30 – 60 mins once |
Backwash Time | 30-60seconds |
Chemical Enhanced Backwash Frequency: | 0 – 4 times per day |
Chemical Enhanced Backwash Duration: | 5 – 10 minutes |
Chemical cleaning frequency | 1-3 months |
Cleaning Chemicals |
|
sterilization | |
Organic pollution cleaning | 0.2% Sodium hypochlorite 0.1%Sodium hydroxide |
Inorganic contamination cleaning | 1-2% Citric acid, 0.2% Hydrochloric acid |
Material
Part | Material |
Hollow fiber | Reinforced PVDF |
Potting | Epoxy Resin |
Housing | UPVC |
Hollow fiber ultrafiltration UF module
1. Product introduction:
JXUF250-Max 80 ultrafiltration membrane is a capillary hollow fibre membrane, which is a kind of polymer material membrane, it is a kind of separation product without phase change. The modified PES material used in this product has good water permeability, mechanical properties, chemical resistance and anti-pollution ability.
JXUF250-Max 80
The membrane module is installed with hollow membrane filament with inner diameter of 0.8mm and outer diameter of 1.3mm. The filtration method is internal pressure, i.e., the raw water is driven by the pressure difference and enters into the inner part of the hollow filament, and permeates through the hollow filament along the radial direction from the inside to the outside. Thus, it can filter
It can remove all kinds of bacteria, colloid, suspended solids, microorganisms and other harmful substances in the raw water.
2. Application:
● Mineral water, mountain spring water and other sterile liquid preparation;
● Drinking treatment of tap water surface water, well water and river water;
● Pre-treatment of RO reverse osmosis device;
● Industrial wastewater treatment, recycling and utilization.
3. Filtration performance
This product achieves the following filtering effects:
Composition of water | Result |
Suspended matter, particles >1um | Remove rate ≥99% |
SDI | Produced ≤3 |
Viruses, Bacteria | >4 log |
Turbidity | Produced <0.1NTU |
TOC | Remove rate 0-25% |
The above data is obtained when the influent turbidity is less than 25NTU.
4. Produce parameters
Performance:
Structure | Out-side in |
Membrane material | Reinforced PVDF |
Membrane area | 105m2 |
Fiber dia. | ID:0.8mm, OD:1.3mm |
Outside dimension | Dia.250mm*2340mm |
Connector size | DN50(Match DN40 joint) |
MWCO | 200000DAL |
Application data:
Typical Filtrate Flux Range | 18800L/H(0.15Mpa,25℃) |
Design Flux | 35-100L/m2.h (0.165Mpa, 25℃) |
Normal working pressure | ≤0.2MPa |
Maximum Transmembrane Pressure | 0.15Mpa |
Maximum backwash Pressure | 0.15Mpa |
Volume of air wash | 0.1-0.15N m3/m2.h |
Air pressure | |
Maximum Operating Temperature | (45°C |
pH Operating Range | 4.0 - 10.0 |
Cleaning pH Range | 4-10 Operating, Cleaning 2-12 |
Operating Mode | Full filtration or Crossflow |
Feed requirements:
A security filter of less than 50 microns is added before the water intake to prevent the machine from being clogged by large particles in the raw water.
The machine is clogged by large particles in the raw water. Note: The ultrafiltration membrane is made of high polymer organic plastic, and the raw water must not contain organic solvents!
Feed Turbidity | ≤25NTU |
Oil | ≤2mg/L |
Feed SS | ≤20mg/L |
Total Iron | ≤1mg/L |
Residual chlorine from continuous inlet water | ≤5ppm |
COD | ≤500mg/L |
Typical Process Conditions
Backwash Pressure | 0.15MPa |
Backwash Flux: | 100 – 150L/m2.h |
Backwash Frequency: | 30 – 60 mins once |
Backwash Time | 30-60seconds |
Chemical Enhanced Backwash Frequency: | 0 – 4 times per day |
Chemical Enhanced Backwash Duration: | 5 – 10 minutes |
Chemical cleaning frequency | 1-3 months |
Cleaning Chemicals |
|
sterilization | |
Organic pollution cleaning | 0.2% Sodium hypochlorite 0.1%Sodium hydroxide |
Inorganic contamination cleaning | 1-2% Citric acid, 0.2% Hydrochloric acid |
Material
Part | Material |
Hollow fiber | Reinforced PVDF |
Potting | Epoxy Resin |
Housing | UPVC |
Attention |
Package size
The membrane modules are added with glycerin protective liquid, and they are individually packaged when leaving the factory. The membrane modules are wrapped in plastic film bags, sealed and placed in a rigid cardboard box with shock-proof and fixing measures.
Storage (use) precautions
If the membrane module is not installed and used temporarily, it should be stacked on a flat and clean indoor floor, away from cold and heat sources, to ensure that there is no corrosion and pollutants around; the storage temperature is controlled at 5-40 °C, and the recommended storage temperature is 20-35 °C .
Warranty
Keep the membrane modules in the original packaging as much as possible. Under the above storage conditions, unopened new membrane modules can be stored for 2 years.
Disclaimer
The indicators and data given in this document are based on our existing technical knowledge level and practical experience and are for reference only. The specific guarantee indicators are otherwise agreed in the technical agreement or supply contract
Subject to agreement. It is the user's responsibility to test the products purchased by our company to verify whether they are suitable for their respective proposed processes and uses, and to achieve the intended purpose.
The conditions and methods of using the company's products are beyond the control of our company, therefore, our company is not responsible for the results and damages arising from the use of such information and data. Our company technical support and
The customer service center is willing to provide you with product consulting and application technical services. Welcome to contact us by letter or call.
Attention |
Package size
The membrane modules are added with glycerin protective liquid, and they are individually packaged when leaving the factory. The membrane modules are wrapped in plastic film bags, sealed and placed in a rigid cardboard box with shock-proof and fixing measures.
Storage (use) precautions
If the membrane module is not installed and used temporarily, it should be stacked on a flat and clean indoor floor, away from cold and heat sources, to ensure that there is no corrosion and pollutants around; the storage temperature is controlled at 5-40 °C, and the recommended storage temperature is 20-35 °C .
Warranty
Keep the membrane modules in the original packaging as much as possible. Under the above storage conditions, unopened new membrane modules can be stored for 2 years.
Disclaimer
The indicators and data given in this document are based on our existing technical knowledge level and practical experience and are for reference only. The specific guarantee indicators are otherwise agreed in the technical agreement or supply contract
Subject to agreement. It is the user's responsibility to test the products purchased by our company to verify whether they are suitable for their respective proposed processes and uses, and to achieve the intended purpose.
The conditions and methods of using the company's products are beyond the control of our company, therefore, our company is not responsible for the results and damages arising from the use of such information and data. Our company technical support and
The customer service center is willing to provide you with product consulting and application technical services. Welcome to contact us by letter or call.